ADIY
MQ135 Gas Sensor ModuleFIG. 01

Gas Sensors

MQ135 Air Quality Sensor Module – ADIY

MQ-135 Gas sensor can detect gases like Ammonia (NH3), sulfur (S), Benzene (C6H6), CO2, and other harmful gases and smoke. Similar to other MQ series gas sensor, this sensor also has a digital and analog output pin.…

₹119₹250incl. GST · price as listed

In stock (as listed)

Overview

MQ-135 Gas sensor can detect gases like Ammonia (NH3), sulfur (S), Benzene (C6H6), CO2, and other harmful gases and smoke. Similar to other MQ series gas sensor, this sensor also has a digital and analog output pin. When the level of these gases go beyond a threshold limit in the air the digital pin goes high. This threshold value can be set by using the on-board potentiometer. The analog output pin, outputs an analog voltage which can be used to approximate the level of these gases in the atmosphere. The MQ135 air quality sensor module operates at 5V and consumes around 150mA. It requires
some pre-heating before it could actually give accurate results.

Application:MQ135 Gas Sensor Module

  • Used as air quality monitors.
  • Used as a domestic air pollution detector.
  • Used in the detection of excess or leakage of gases

MQ135 Gas Sensor Module is made using Air Quality Gas Sensor MQ135. It is a low-cost semiconductor sensor and has high sensitivity to ammonia gas, sulphide, benzene series steam, also can monitor smoke and other toxic gases well. It is a Metal Oxide Semiconductor (MOS) type Gas Sensor also known as Chemin resistors as the detection is based upon change of resistance of the sensing material when the Gas comes in contact with the material. Using a simple voltage divider network, concentrations of gas can be detected. This module provides both digital and analog outputs. It can be easily interfaced with Microcontrollers, Arduino Boards, Raspberry Pi etc.

Features – MQ135 Gas Sensor Module#

  • Wide detecting scope
  • Fast response and High sensitivity
  • Stable and long-life Simple drive circuit
  • Used in air quality control equipment for buildings/offices, is suitable for detecting of NH3,NOx, alcohol, Benzene, smoke, CO2, etc.
  • Size: 35mm x 22mm x 23mm (length x width x height)
  • Signal output instruction.
  • Dual signal output (analog output, and high/low digital output)
  • 8. 0 ~ 4.2V analog output voltage, the higher the concentration the higher the voltage

Specifications – MQ135 Gas Sensor Module#

  • Operating Voltage: 2.5V to 5.0V
  • Power consumption: 150mA
  • Detect/Measure: NH3, Nox, CO2, Alcohol, Benzene, Smoke
  • Typical operating Voltage: 5V
  • Digital Output: 0V to 5V (TTL Logic ) @ 5V Vcc
  • Analog Output:0-05 V@ 5V Vcc

Technical details: – MQ135 Gas Sensor Module#

The MQ135 is one of the popular gas sensors from the MQ series of sensors that are commonly used in air quality control equipment. It operates from 2.5V to 5.0V and can provide both digital and analog output.
Note that all MQ sensors have to be powered up for a pre-heat duration for the sensor to warm up before it can start working.
This pre-heat time is normally between 30 seconds to a couple of minutes. When you power up the module the power LED will turn on, leave the module in this state till the pre-heat duration is completed

Pin Configuration:- MQ135 Gas Sensor Module#

  • VCC: It is used to connect 5V to the sensor.
  • GND: It is used to connect GND to the sensor.
  • DO: It is a digital output Pin. From this pin, you will get digital data HIGH/LOW.
  • The digital output pin of the sensor can be used to detect harmful gases in the environment. The sensitivity of the digital pin can be controlled by using the 10k potentiometer. If the gas is detected the indicator LED D0 will turn on and the digital pin will go from logic high to logic
  • low (0V). The LM393 Op-Amp Comparator IC is used to compare the actual gas value with the value set using the potentiometer. If the actual gas value increases than the set value then the digital output pin gets low.

Pin Configuration: MQ-135 Gas sensor Module

Pin Configuration: MQ-135 Gas sensor Module

Because of the onboard LM393 comparator IC the MQ135 Gas sensor module can also be used without the need of an external microcontroller. Simply power up the module and set the sensitivity of the digital pin using the potentiometer, then when the module detects the gas the
digital pin will go low. This digital pin can directly be used to drive a buzzer or LED with the help of simple transistors. AO: It is analog output Pin. From this pin, you will get analog data. The Analog output pin of the sensor can be used to measure the PPM value of the required gas. To do this we need to use an external microcontroller. The microcontroller will measure the value of analog voltage and perform some calculations to find the value of Rs/Ro where Rs is the
sensor resistance when gas is present and Ro is sensor resistance at clean air.

Resources:MQ135 Gas Sensor Module#

Features

  • Used as air quality monitors.
  • Used as a domestic air pollution detector.
  • Used in the detection of excess or leakage of gases
  • Wide detecting scope
  • Fast response and High sensitivity
  • Stable and long-life Simple drive circuit
  • Used in air quality control equipment for buildings/offices, is suitable for detecting of NH3,NOx, alcohol, Benzene, smoke, CO2, etc.
  • Signal output instruction.
  • Dual signal output (analog output, and high/low digital output)
  • 8. 0 ~ 4.2V analog output voltage, the higher the concentration the higher the voltage
  • low (0V). The LM393 Op-Amp Comparator IC is used to compare the actual gas value with the value set using the potentiometer. If the actual gas value increases than the set value then the digital output pin gets low.
  • MQ-135 Arduino Library
  • Interfacing MQ135 with Arduino

Technical specifications

Specifications for MQ135 Air Quality Sensor Module – ADIY
Size35mm x 22mm x 23mm (length x width x height)
Operating Voltage2.5V to 5.0V
Power consumption150mA
Detect/MeasureNH3, Nox, CO2, Alcohol, Benzene, Smoke
Typical operating Voltage5V
Digital Output0V to 5V (TTL Logic ) @ 5V Vcc
Analog Output0-05 V@ 5V Vcc
VCCIt is used to connect 5V to the sensor.
GNDIt is used to connect GND to the sensor.
DOIt is a digital output Pin. From this pin, you will get digital data HIGH/LOW.

Specifications are taken from the product listing. See the datasheet for full electrical details.

Pin configuration

MQ135 GAS SENSOR MODULE_Pin diagram

Datasheets & downloads

  • Mq 2 gas sensor

    Gas Sensors

    ADIY MQ2 Gas Sensor Module

    ADIY MQ2 gas sensor is an electronic sensor used for sensing the concentration of gases in air such as LPG, Propane, Methane, Hydrogen, alcohol, smoke, and carbon monoxide. MQ2 gas sensor is also known as chemiresistor.…

    ₹109

    Datasheet
  • MQ3-GAS-SENSOR-MODULE

    Gas Sensors

    MQ3 Gas Sensor Module – ADIY

    MQ3 Alcohol Sensor Module is made using Alcohol Gas Sensor MQ3. It is a low-cost semiconductor sensor that can detect the presence of alcohol gases at concentrations from 0.05 mg/L to 10 mg/L. The sensitive material…

    ₹125

    Datasheet
  • MQ4 gas sensor Module

    Gas Sensors

    MQ4 Methane CNG Gas Sensor Module – ADIY

    MQ4 methane gas sensor Module is designed to detect methane (CH4) and CNG gas leaks in homes and industries. It provides rapid response and high sensitivity, adjustable via a potentiometer. The sensor outputs an analog…

    ₹110

    Datasheet
  • MQ5-Methane LPG Gas Sensor Module

    Gas Sensors

    MQ5 Gas Sensor Module – ADIY

    ADIY MQ5 gas sensor module is used in gas leakage detection, and suitable for home and industrial equipment for LPG, natural gas, coal gas detection and monitoring. The sensitive material used in the MQ5 gas sensor is…

    ₹110

    Datasheet